Home / Technology / Identix SLP: loss prevention at the store exit

Identix SLP: loss prevention at the store exit

Identix SLP is the loss-prevention solution for retail: a custom firmware that coordinates every reader at the exit, in ExitView towers or in an overhead portal, and decides who is leaving the store with unpaid goods. It runs on the IRIS controller that drives the readers and adds to CONNECTIX brAIn the algorithms made for loss prevention. It is in development, and you can see it today in the simulators.

Why the store exit needs a solution of its own

A dock door or a conveyor reads a load. A store exit reads people: several of them side by side, carrying bags, walking by in front of the exit without leaving, restocking the rack beside it. The decision has to be made while the person is still at the door, and a false alarm stops a customer who did nothing wrong. Each reader deciding alone, even with brAIn, cannot tell which lane a person crossed when several towers read the same item.

Two customers in neighbouring lanes. Each one has to alarm in their own lane.

Standard ExitView
inside the storeway out123every tower that reads sounds
Identix SLP
inside the storeway out123lanes 1 and 2 sound, lane 3 stays quiet

Walking by, not leaving. A person walks along the row inside the store with products in hand.

Standard ExitView
inside the storeway out123the towers it passes sound
Identix SLP
inside the storeway out123no alarm: nobody crossed

One item, three towers. The item crosses lane 2 and towers 1, 2 and 3 read it.

Standard ExitView
inside the storeway out1233 eventsthree alarms, wrong lane included
Identix SLP
inside the storeway out1231 event, lane 2one alarm: the two towers of lane 2

Seen from above, four towers and three lanes; an orange tower sounds. Illustrative, not to scale.

  • Two customers leave together through neighbouring lanes: each must alarm in their own lane. SLP treats the row of towers as one point of exit and gives one event per item, in the lane crossed, sounding only that lane's two towers.
  • A person walks along the row inside the store with products in hand: a tower on its own sounds as soon as it reads them. SLP tells walking by from crossing.
  • One item read by three towers is three alarms in the standard ExitView. With SLP it is one alarm, in the right lane.
  • Two antennas facing each other across a lane disturb each other when they transmit at the same time. SLP takes turns between them, and the outer antenna of each end tower, which only looks into the store, stays idle.

SLP and brAIn: what is different

brAIn is part of every Identix reader; SLP is a loss-prevention solution built on top of it.

Standard ExitView
reader 1brAIndecisionreader 2brAIndecisionreader 3brAIndecisionreader 4brAIndecisionEach reader filters its own readsand decides alone
Identix SLP
reader 1brAInreader 2brAInreader 3brAInreader 4brAInSLP: one decision for the exitOne event per item, in the lanecrossed, for the whole exit

CONNECTIX brAIn

Algorithms, deterministic or with machine learning, that filter unwanted reads and tell the transition between zones. They run in each reader, with that reader's reads, in every use case: dock, conveyor, tunnel, point of sale and store exit. Standard firmware of Identix readers.

Identix SLP

A custom loss-prevention firmware on the controller that drives all the readers of the exit. It does everything brAIn does and adds the coordination between readers, which is always SLP, and the loss-prevention algorithms tied to the reader firmware. Only for loss prevention, with towers or overhead.

The standard ExitView is the ExitView tower with its EM300 (E310 chip) and brAIn, without SLP: the goods standing still on a rack beside the exit make no alarm, but each tower still decides alone.

Towers or overhead

Towers
ExitView towers: special EM300, E510 chipIRIS controller · SLPstore systems (MQTT)
Overhead
EZ700 (default) or EZ500IRIS controller · SLPstore systems (MQTT)

In both layouts one controller runs SLP and drives every reader of the exit. Illustrative, not to scale.

ExitView towers with SLP

The same ExitView towers with a special EM300 on the E510 chip, coordinated by SLP. For exits with one or more lanes between towers.

Overhead portal with SLP

An EZ700 (the default) or an EZ500 with the SLP firmware, on the ceiling of the entrance. For wide entrances with no room for towers.

One controller

An IRIS controller runs SLP and drives every reader of the exit, so the decision is made once for the whole exit and each event goes to the store's systems.

How the algorithms are chosen

Like brAIn, the SLP algorithms are designed, trained and validated on simulated store exits before they reach a tower: the same scenes are scored with the raw reads, with the standard ExitView and brAIn, with an SLP deterministic rule and with an SLP machine-learning model. The rule stays when it ties; the model only goes in when it clearly does better.

Identix SLP is in development and not yet validated in the field. Every number the simulators show is a simulation, with its premises on screen.

See it in the simulators

Open the ExitView simulator, put a rack beside the exit and a person walking by in front, and switch between the standard ExitView, brAIn and SLP. The SLP simulator shows the overhead portal at a wide entrance.

Questions we hear

Does SLP replace brAIn?

No. SLP includes what brAIn does and adds the coordination between readers and the loss-prevention algorithms.

Is the standard ExitView not enough?

For an exit with one lane and little traffic around it, it can be. With several lanes, people walking by in front of the row or customers leaving together, the towers need to decide together, and that is SLP.

Does it work without towers?

Yes. At an entrance with no room for towers, SLP runs on an overhead EZ700 (the default) or EZ500 on the ceiling.

Can I buy it today?

Identix SLP is in development. If you are planning loss prevention for a store, talk to us: we will look at the exit and at what SLP could add.

Need help connecting it?

Talk to an engineer