Home / Technology / E310, E510 or E710: which reader fits your operation?

E310, E510 or E710: which reader fits your operation?

Identix readers are built on three Impinj chips. Here is what changes in speed, sensitivity and the ability to identify products in real conditions.

Three chips, three application profiles

Asking how many tags a reader reads per second is not enough. The more useful question is: does it identify the right items, in the time the operation allows, even when conditions are not ideal?

All three identify RAIN RFID tags without line of sight. The difference is the operating margin available to face harder situations.

Impinj chipIdentix productsWhere it usually works bestWhen to step up
E310EM300 EM300H DR-max DR-mini DR-pad SAMDK-300 SAM300 MB300Controlled read points, few tags at a time, counters and close-range checks.Many items at once, fast passes and weak tag replies.
E510EZ500 SAMDK-500 SAM500 MB500Conveyors, logistics, box handling and portals where the tag position varies more.High density, people walking through and a strict read target.
E710EZ700 ID50 SAMDK-700 SAM700 MB700The most demanding sites: heavy flow and a real need for receive margin.Even the E710 needs the right antennas and tags; it does not remove physical blocking.

1. How RFID identifies an item

The reader sends energy and commands through the antenna. The RFID tag on the product takes part of that energy to power its circuit and replies by reflecting a small part of the signal. The reader recognizes the reply and hands the code to the system.

The link has to work both ways. On the way out, the tag must receive enough energy. On the way back, the reader must hear a very weak reply. More power helps the first step; better sensitivity mainly helps the second.

Think of a conversation in a noisy room: speaking louder helps the question arrive. Hearing better helps you understand the answer. They are different advantages, and both depend on the room.

Readerantennatag on the product1. Energy and commands2. Very weak reflected replyMore power helps step 1 · better sensitivity helps step 2A passive tag has no battery: it runs on the energy it receives

2. What 300, 750 and 1,100 reads per second mean

A read is one reply received from a tag. The same tag can reply many times. A system may log a thousand events that all come from only 100 products. In that case the inventory found 100 different items, not a thousand.

“Up to 300”, “up to 750” and “up to 1,100” are the maximum nominal capacity under favourable conditions. They do not promise that many different items every second, nor that every reader mode delivers the top rate.

In practice a reader can pick a more careful mode to recognize difficult replies. That usually lowers the raw speed but can raise the number of distinct items found. If 120 parts cross a conveyor in one second, a nominal 750 reads/s does not automatically mean all 120 are found: some may be hidden by liquids, metal, other packages or the way the tag faces.

Top speed and top sensitivity never come together. On the E710 chip, the fastest mode reads about 1,100 tags/s but only hears replies down to about −71 dBm; the most sensitive mode hears −88 dBm at about 75 tags/s. The table below shows the Identix datasheet figures and, under it, Impinj's figures for the chip alone.

Identix reader datasheetsE310 readersE510 readersE710 readers
Reads per second (up to)3007501,100
Receive sensitivity−75 dBm−82 dBm−86 dBm
Maximum RF power+27 to +33 dBm, by product+30 to +33 dBm, by product+30 to +33 dBm, by product
Example: fixed readerEM300 · +30 dBm · 4 × SMAEZ500 · +31.5 dBm · 4 × TNCEZ700 · +33 dBm · 4 × TNC

Nominal values stated for the Identix products of each chip. Maximum rates describe the capacity to process events, not a guaranteed number of distinct products. Output power is set by the design of each product, not by the chip.

Impinj chip referenceE310E510E710
Fastest RF mode: tags/s · sensitivity316 · −65.0 dBm791 · −68.6 dBm1,103 · −71.3 dBm
Most sensitive RF mode: tags/s · sensitivity72 · −74.8 dBm75 · −82.2 dBm75 · −88.0 dBm
Chip output powerup to +11 dBm; the product amplifier sets the final powerup to +11 dBm; the product amplifier sets the final powerup to +11 dBm; the product amplifier sets the final power

Sources: Impinj E910/E710/E510/E310 Performance application note (read rate with 400 tags, sensitivity at the development-board antenna port) and Impinj E-series datasheet v1.4. The top rate and the best sensitivity come from different RF modes and never happen at the same time. The Identix figures above match these chip limits.

3. Sensitivity: hearing very weak replies

Sensitivity is the weakest signal the reader can recognize. It is given in dBm; since tag replies are very weak, the numbers are negative. A more negative number means a receiver that hears an even weaker signal.

So, by the Identix reader datasheets, the E510 (−82 dBm) has a nominal 7 dB advantage over the E310 (−75 dBm), and the E710 (−86 dBm) adds another 4 dB over the E510. That can matter when the tag replies at the edge, for example behind other goods or close to the body.

It does not mean the E710 always reads farther, nor that its success rate is higher everywhere. If the tag cannot power up, there is no reply for the receiver to hear. Coverage, cable, the power actually allowed, the tag and the material still decide.

4. Link budget: the energy left when it reaches the tag

A link budget adds up what helps and what hurts the signal. The reader starts with some power; the cable loses a little; the antenna concentrates energy in the chosen direction; distance, the product and obstacles keep lowering the level that reaches the tag.

Step in the exampleBalance or effectWhat happens
Power at the reader port+27 dBmStarting point of the example
Cable loss−1 dBPart of the energy stays in the cable
Gain toward the useful direction+6 dBiThe antenna concentrates energy that way
Free-space loss at 3 m−41.2 dBThe signal weakens along the way
Polarization mismatch−3 dBPart of it is not picked up
Power at the tag (approx.)−12.2 dBmBalance before other real-world effects

Illustrative values to explain the reasoning; they are not the guaranteed range of any product. Radiated power must stay within the regulatory limits of the installation.

If a hypothetical tag needed at least −18 dBm to work, this example would leave about 5.8 dB of margin. Losing another 6 dB to position, wet clothing or packaging is enough to stop the read. Then comes the way back: the tag returns a weak signal over the same path, and that is where the sensitivity of the E310, E510 or E710 can make the difference.

5. The tag and the antenna also set the result

Two tags with the same code can perform very differently. A tag made for cardboard can lose performance when stuck directly on metal; a small tag usually has less margin than one designed for the application; and its position on the package changes the energy that reaches the chip.

Linear antennas work especially well when the tag orientation is known and repeatable. Circular antennas help where tags arrive rotated, as in walkways, boxes and carts. Gain and beamwidth decide whether the signal covers a wide area or concentrates on a narrower strip.

That is why there is no “reader read range” independent of everything else. In many projects, moving the antenna or choosing the right tag improves the result more than adding power.

6. One radio, four antennas: how time is shared

Four-port readers, such as the EM300, EZ500 and EZ700, drive four antennas from one radio. When switching, it talks to one antenna at a time: the first, then the second, third and fourth, and repeats. Each port can have its own settings, but that does not turn one radio into four independent receivers.

With four antennas served equally, each gets about a quarter of the radio time. If a reader mode produces 750 events per second with one antenna always on, the idealized total stays close to 750 events per second shared by the four, not 3,000. In practice there are switching, command and reception losses.

During a 200 ms visit to one antenna, that same illustrative ceiling would be 60 events on the E310, 150 on the E510 and 220 on the E710. These are only 0.2 s times the nominal maximum rate; they are not unique items or measurements with four ports.

Four antennas widen the directions you look from, but they do not multiply instantaneous speed. A product that stays only 150 ms in one antenna's zone can pass between two visits of the radio. For very fast passes it may be better to tune dwell times, trigger reading with sensors or split the installation across more than one radio.

Antenna 1200 msAntenna 2200 msAntenna 3200 msAntenna 4200 msOne radio visits one antenna at a time · cycle of 800 msa tag only 150 ms in front of antenna 1 can be missedEach antenna gets about 25% of the radio time · teaching example

7. How materials and people get in the way

The human body holds a lot of water. At UHF it can absorb part of the energy meant for the tag and also weaken the reply. It gets worse when the tag touches the skin, is covered by people or hangs badly on clothing. It is not only distance: someone two metres away with the tag facing the antenna can be easier to read than someone at one metre whose body blocks the path. Wet clothes, water bottles and full bags do the same.

SituationWhat changesGood practice
Metal and cartsReflections, and common tags go out of tune.On-metal tags; several antenna positions.
Water, drinks, damp fabricMore energy absorbed, especially right next to the tag.Test with the real product at several moisture levels.
Stacked productsItems in front can hide the ones behind.Read from more than one side and allow more time.
Human bodyHigh water content weakens the signal; the torso casts shadows.Antennas at complementary angles and well-placed tags.
Neighbouring readersInterference makes weak replies harder to hear.Plan the installation, channels and reader mode.

8. Retail loss prevention: why E510 and E710

At a store exit the reader must identify the tags crossing the walkway but not catch the products still on nearby shelves. People leave side by side, carry bags and can hide tags with their own bodies. Some products sit in packaging with liquids or metal.

In an empty, controlled walkway an E310 reader can be enough. With heavy flow, several people at once, tags close to the body and little time to decide whether an item is leaving, the E510 or E710 offers more nominal margin of speed and sensitivity. That is the technical reason to favour them in the toughest loss-prevention scenarios.

The E510 tends to serve gates with moderate to high flow, as long as antennas and tags are sized well. The E710 deserves preference at exits with more people and products, fast passes or low signal margin. Neither removes the need to bound the zone well and test false alarms and missed reads.

Try it in the simulator: Store exit ExitView

9. Road race timing: when every fraction of a second counts

In road races many runners cross almost together. The tag may sit on the race bib, close to the body, under wet clothing or bent by movement. RFID has little time to identify it and tell neighbouring runners apart, even when they overlap in the antenna field.

The challenges stack up: the body absorbing signal, varying tag orientation, dense groups and short read windows. The E510, and above all the E710, are better choices than the E310 when the system depends on fast, reliable identification in a crowded pass, because they offer more receive margin and nominal capacity for read events.

For a start or finish with many people, the antenna design is decisive. Side and overhead antennas can create complementary chances but must be validated with the real tag position on the chest. When precise timing and runner traceability are required, capture architecture, timing sensors, redundancy and field tests have to be planned together with the reader.

Practical advice: for timing and complex loss prevention, start the evaluation with the E710 and consider the E510 when the flow and geometry allow. Do not promise 100% reads or timing precision based only on the nominal tags/s rate.

10. Other scenarios that help you choose

ScenarioStarting choiceWhy
Counter or check of a few itemsE310Close-range reads, enough time and low complexity.
Conveyor with well-placed boxesE510More headroom for flow and tags in different orientations.
Dock door or dense palletsE510 / E710More items, mixed materials and little chance to repeat the pass.
Laundry with damp garmentsE510 / E710Wet fabric, hidden tags and large batches.
Busy store exitE710People and bags cast shadows and leave short windows.
Road race timing gateE710Many runners together, the human body and little read time.

In short: E310 for controlled read points; E510 for more flow and variety; E710 for the most demanding uses, including busy exits and timing. These are starting points: even the E710 depends on suitable tags, antennas and installation.

11. How to validate the application before deployment

  • Set the goal in unique items: of 500 products crossing the portal, how many must be identified correctly before they leave the zone?
  • Reproduce the real speed, height, orientation and mix of items, including people, metal, liquids and tags close to the skin.
  • Use the same antennas and tags in the comparison; record allowed power, position, cable losses, time per port and reader mode.
  • Repeat the tests at different occupancy: empty walkway, normal flow and worst case, including dense groups of people.
  • Measure the rate of unique tags identified, missed reads, duplicates and unwanted reads outside the zone, not only events per second.
Simulate before you choose: RFID simulators Talk to an engineer

Questions we hear

Which Identix products use each chip?

E310: EM300, EM300H, DR-max, DR-mini, DR-pad, SAMDK-300, SAM300 and MB300. E510: EZ500, SAMDK-500, SAM500 and MB500. E710: EZ700, the ID50 handheld, SAMDK-700, SAM700 and MB700.

Does an E710 reader always read farther?

No. Its better sensitivity helps hear weak replies, but the tag still has to receive enough energy to answer. Antenna, cable, allowed power, tag and material still set the range.

Do four antennas read four times faster?

No. One radio serves one antenna at a time, so the total stays close to the reader's nominal rate. Four antennas add viewing directions, not instantaneous speed.

Need help connecting it?

Talk to an engineer